View in EDS

Mitigation of Current Distortion in a Three-Phase Microinverter With Phase Skipping Using a Synchronous Sampling DC-Link Voltage Control.

Saved in:
Bibliographic Details
Title: Mitigation of Current Distortion in a Three-Phase Microinverter With Phase Skipping Using a Synchronous Sampling DC-Link Voltage Control.
Authors: Tayebi, S. Milad1, Batarseh, Issa1
Source: IEEE Transactions on Industrial Electronics. May2018, Vol. 65 Issue 5, p3910-3920. 11p.
Subjects: Bus conductors (Electricity), Capacitors, Voltage-frequency converters, Electric capacity, Photovoltaic power generation
Abstract: To improve light load efficiency, a three-phase photovoltaic (PV)-based microinverter may operate in single-phase, two-phase or three-phase mode depending on the available input power. Therefore, its dc-link capacitor may be subjected to large peak-to-peak voltage ripple when operating in phase skipping mode. This paper determines the minimum value of the dc-link capacitor by allowing the maximum acceptable voltage ripple on the dc link. This allows for the use of film capacitors instead of electrolytic capacitors in order to improve the microinverter reliability. Unfortunately, higher dc-link voltage ripple introduces harmonic distortion on the inverter output current waveform if it is not compensated for by the dc-link voltage controller. This paper proposes a simple synchronous control method to regulate the dc-link voltage with the presence of large voltage ripple. The dc-link voltage controller is synchronized with the phase-locked loop and samples the average value of dc-link voltage without introducing unwanted harmonics into the voltage sense path. Experimental results were obtained from a 300-W three-phase half-bridge microinverter prototype to verify the proposed dc-link voltage control performance. Inverter output current total harmonic distortion of 1.6% was achieved even though the dc-link peak-to-peak voltage ripple reached as high as 87 V with 219-V split dc-link voltage. Dynamic response is fast enough to easily track the most extreme ramp change in input PV power. [ABSTRACT FROM PUBLISHER]
Copyright of IEEE Transactions on Industrial Electronics is the property of IEEE and its content may not be copied or emailed to multiple sites without the copyright holder's express written permission. Additionally, content may not be used with any artificial intelligence tools or machine learning technologies. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)
Database: Engineering Source
Description
Abstract:To improve light load efficiency, a three-phase photovoltaic (PV)-based microinverter may operate in single-phase, two-phase or three-phase mode depending on the available input power. Therefore, its dc-link capacitor may be subjected to large peak-to-peak voltage ripple when operating in phase skipping mode. This paper determines the minimum value of the dc-link capacitor by allowing the maximum acceptable voltage ripple on the dc link. This allows for the use of film capacitors instead of electrolytic capacitors in order to improve the microinverter reliability. Unfortunately, higher dc-link voltage ripple introduces harmonic distortion on the inverter output current waveform if it is not compensated for by the dc-link voltage controller. This paper proposes a simple synchronous control method to regulate the dc-link voltage with the presence of large voltage ripple. The dc-link voltage controller is synchronized with the phase-locked loop and samples the average value of dc-link voltage without introducing unwanted harmonics into the voltage sense path. Experimental results were obtained from a 300-W three-phase half-bridge microinverter prototype to verify the proposed dc-link voltage control performance. Inverter output current total harmonic distortion of 1.6% was achieved even though the dc-link peak-to-peak voltage ripple reached as high as 87 V with 219-V split dc-link voltage. Dynamic response is fast enough to easily track the most extreme ramp change in input PV power. [ABSTRACT FROM PUBLISHER]
ISSN:02780046
DOI:10.1109/TIE.2017.2760864